Search

New products

  • £ 2.58
    £ 2.58

    The Wemos triple base (HCWEMO0016) is designed to allow a Wemos shield to be connected to a Wemos D1 board without having to use the normal stacking method. This is useful when you have multiple shields that are not suited for stacking together such as an OLED shields with sensor/relays shields, or where a lower profile is preferred. Supplied with the...

  • £ 2.50
    £ 2.50

    The Wemos dual base (HCWEMO0015) is designed to allow a Wemos shield to be connected to a Wemos D1 board without having to use the normal stacking method. This is useful when you have multiple shields that are not suited for stacking together such as an OLED shields with sensor/relays shields, or where a lower profile is preferred. Supplied with the...

  • £ 6.99
    £ 6.99

    These self healing cutting mats measure 45cm x 30cm (A3). Perfect for areas where you need to protect your surfaces from cuts and scrapes as you work and are ideally suited to a wide range of drafting and cutting applications.

  • £ 19.99
    £ 19.99

    This Sonoff 4CH 4-gang switch with din rail mounting supports connections for 4 electrical appliances, which can be turned on/off separately by the buttons or iOS/Android App EweLink. Additionally, you can check the real-time status of connected devices using the App.

  • £ 4.99
    £ 4.99

    This 66mm module contains a strip of 24 individually controllable RGB LEDs arranged in a circular serial configuration. Each LED has seperatly controllable red, green, and blue, elements which can be individually set to one of 256 different intensity settings, allowing over 16 million colour variations. The module also has power and data connections at...

  • £ 24.00
    £ 24.00

    Sonoff B1 is white and color ambiance dimmable LED bulb with E27 screw base. The dimming led lamp can be dimmed or brightened via the iOS/Android App. With the App, you can select simple white or you can set a colour and even change the temperature from cold to warm and change the brightness from 1%-100%.

  • £ 13.99
    £ 13.99

    This electric desoldering iron melts and removes solder quickly and easily.It replaces the conventional method of desoldering components, by combining a desolder pump and a 40W/230V mains powered soldering iron into one easy to use tool.To operate, the plunger is pressed down until it locks...

  • £ 4.99
    £ 4.99

    This strain gauge module uses a BF350 sensor to measure mechanical stresses in solid materials. The module includes an adjustable amplifier circuit to make it suitable for interfacing directly to a microcotrollers ADC input and requires only a single 5V power supply.Note that this module should be used for applications where only relative strain...

  • £ 1.98
    £ 1.98

    A resistive strain gauge sensor with a 350 ohm nominal resistance which varies when a force is applied. By measuring the change in the sensors resistance a measurement of the force applied to it can be obtained. Note that strain gauges exhibit small changes in resistance and so this sensor should be used in a Wheatstone bridge...

  • £ 9.99
    £ 9.99

    The VL53L0X (HCMODU0127) is a new generation Time-of-Flight (ToF) laser-ranging module housed in the smallest package on the market today, providing accurate distance measurement whatever the target reflectances, unlike conventional technologies. It can measure absolute distances up to 2m, setting a new benchmark in ranging performance levels, opening the...

  • £ 3.99
    £ 3.99

    The STM32F103C8T6 (HCDVBD0033 / Black pill) Development Board is a low cost but feature rich alternative to an Arduino. The board features an ST Microelectronics STM32F103C8 Arm microprocessor running at a 72MHz clock speed. Coupled with 64K of Flash and 20K of SRAM this development board provides a powerful alternative to an Arduino. This development...

  • £ 16.99
    £ 16.99

    The Aosong AM2315 is a wall mountable temperature and humidity sensor (HCSENS0043) based on the AM2315 capacitive digital sensor. It provides a two wire digital I2C output suitable for interfacing to most 3.3V and 5V microcontrollers and can be powered from a 3.5V to 5.5V (5V recommended) power supply. The sensor is encased in a durable ABS plastic case...

  • £ 12.99
    £ 12.99

    The BN-SZ01 flush mount wireless round LED ceiling light is a wifi controlled cold light led. Designed to be retro-fitted in to an existing light fitting this LED light also includes magnets on the base for screw-less attachemt to any fitting with a metal base. After adding the wireless LED light to the eWeLink app, you can then remotely turn it on or off.

  • £ 6.00
    £ 6.00

    Sonoff SV(safe voltage) is a low power supply Sonoff ESP8266 based development board which supports 5-24V power supply. The power separation circuit enables it to control AC or DC power for the connected device, but you need to do some soldering to use this function, please refer to the soldering instructions below. Sonoff SV has GPIO reserved to support...

  • £ 24.99
    £ 24.99

    The Sonoff SC is an ESP8266 based WiFi environmental monitor device. It detects current temperature, humidity, light intensity, air quality (particulate), and even sound levels (noise pollution), and directly sends real-time data to iOS/Android APP EWeLink.

  • £ 18.99
    £ 18.99

    The Sonoff T1 ESP8266 based UK Wall Touch Switch series are 1-3 gang 86 type touch/App/ RF controlled luxury smart light switches. The wireless wall switch can be added to iOS/Android App eWeLink via WiFi, allowing users to remotely turn on/off connected lights or appliances separately from anywhere at any time. Upgrade your home to an elegant smart home,...

  • £ 15.99
    £ 15.99

    The Sonoff S20 is a smart outlet with UK standard. You can instantly convert any plug into a smart plug with a convenient timer function that works on any iOS or Android smartphone. You can turn on/off any connected device either from within the app eWeLink or by pressing the manual control button of the WiFi outlet. You can set countdown/single/repeat...

  • £ 6.00
    £ 6.00

    This outdoor waterproof case is ideal for both indoor and outdoor use. It is IP66 rated waterproof and can withstand damp and wet conditions, perfect for bathrooms, decorative or seasonal lighting, landscape lighting, fountains, pumps and other home and outdoor plug-in appliances. This is a great waterproof case for many applications, and works well with...

  • £ 7.99
    £ 7.99

    Sonoff is an affordable ESP8266 based device that provides users with smart home control. It is a WiFi based wireless switch that can connect to a wide range of appliances. Sonoff transmits data to a cloud platform through the WiFi router, which enables users to remotely control all the connected appliances, via the mobile application eWeLink. The Sonoff...

  • £ 24.99
    £ 24.99

    Our starter kit is excellent for beginners to the world of Arduino. We have created a project book containing projects that utilise the contents of the kit, including light, sound, temperature and motor projects, to name just a few. All projects come with pre-written sketches and have clear breadboard setup diagrams. The kit also includes our most popular...

  • £ 15.00
    £ 15.00

    PLA, Poly Lactic Acid is probably the best choice when you first start 3D printing. It is refined from corn and grain, and as a biodegradable material, it can be degraded which means it's 100% environmentally friendly. This hard material has excellent strength and stiffness.

  • £ 15.00
    £ 15.00

    PLA, Poly Lactic Acid is probably the best choice when you first start 3D printing. It is refined from corn and grain, and as a biodegradable material, it can be degraded which means it's 100% environmentally friendly. This hard material has excellent strength and stiffness.

  • £ 15.00
    £ 15.00

    PLA, Poly Lactic Acid is probably the best choice when you first start 3D printing. It is refined from corn and grain, and as a biodegradable material, it can be degraded which means it's 100% environmentally friendly. This hard material has excellent strength and stiffness.

  • £ 15.00
    £ 15.00

    PLA, Poly Lactic Acid is probably the best choice when you first start 3D printing. It is refined from corn and grain, and as a biodegradable material, it can be degraded which means it's 100% environmentally friendly. This hard material has excellent strength and stiffness.