Shopping Cart

No products

Free shipping! Shipping
£ 0.00 Tax
£ 0.00 Total

Prices are tax included

Check out

  • Quick view
    £ 8.99
    New

    A larger 1.3" version of our ultra low power tiny uOLED display module. This display has the same 128 x 64 pixel resolution of the smaller 0.96" module but has a significantly larger screen. The module also uses the SH1106 driver which provides a configurable serial interface. By default the display uses a standard SPI interface but it can be reconfigured...

    £ 8.99
    In Stock
  • Quick view
    £ 8.99
    New

    A larger 1.3" version of our ultra low power tiny uOLED display module. This display has the same 128 x 64 pixel resolution of the smaller 0.96" module but has a significantly larger screen. The module also uses the SH1106 driver which provides a configurable serial interface. By default the display uses a standard SPI interface but it can be reconfigured...

    £ 8.99
    In Stock
  • Quick view
    £ 12.99
    New

    One of the most common uses for microcontrollers is for interfacing to various sensors to monitor the world around you. With an Arduino board you can read the value from a temperature sensor and output it to a computer in a matter of minutes. But what if your Arduino and sensor needs to be remotely located and it isn’t practical for it to be tethered to a...

    £ 12.99
    In Stock
  • Quick view
    £ 19.99
    New

    One of the most common uses for microcontrollers is for interfacing to various sensors to monitor the world around you. With an Arduino board you can read the value from a temperature sensor and output it to a computer in a matter of minutes. But what if your Arduino and sensor needs to be remotely located and it isn’t practical for it to be tethered to a...

    £ 19.99
    In Stock
  • Quick view
    £ 2.99
    New

    USB to RS232 TTL PL2303HX auto converter module adapter with a 5V output, which provides the most convenient way to connect your RS232 TTL devices to your computer via the USB port. The cable has a built-in TTL COM PC-PL2303HX Chip and uses a standard USB type A male and TTL 4 pin connector. The cable length is approximately 100cm in length.

    £ 2.99
    In Stock
  • Quick view
    £ 1.49
    New

    Model: MX-FS-03VTransmission Distance :20-200 m (dependent on supply voltage) Operating Voltage :3.5-12V Dimensions: 19 * 19mmAM transfer rate: 4KB / S Transmission power: 10mWEmission frequency: 433M Product Code: HCMODU0088 (Receiver also available: HCMODU0087)

    £ 1.49
    In Stock
  • Quick view
    £ 1.49
    New

    Model: MX-05VWorking voltage: 5V DC quiescent current: 4mAReceiver Frequency: 433.92MHZReceiver sensitivity:-105DBSize: 30 x 14 x 7mmProduct Code: HCMODU0087 (Transmitter also available: HCMODU0088)

    £ 1.49
    In Stock
  • Quick view
    £ 0.49
    New

    These momentary 6mm x 6mm tact switches have 4 DIP pins and feature a long 6mm switch.Product Code: HCSWIT0024Dimensions: 6 x 6 x 9.5mm

    £ 0.49
    In Stock
  • Quick view
    £ 1.49
    New

    These switches are non-latching 4-pin switches. The button is round, mounted in a square casing (top), making them perfect for panel mounting in projects. These are available in red (HCSWIT0034), Green (HCSWIT0035) and Blue (HCSWIT0036).

    £ 1.49
    In Stock
  • Quick view
    £ 1.49
    New

    These switches are non-latching 4-pin switches. The button is round, mounted in a square casing (top), making them perfect for panel mounting in projects. These are available in red (HCSWIT0034), Green (HCSWIT0035) and Blue (HCSWIT0036).

    £ 1.49
    In Stock
  • Quick view
    £ 1.49
    New

    These switches are non-latching 4-pin switches. The button is round, mounted in a square casing (top), making them perfect for panel mounting in projects. These are available in red (HCSWIT0034), Green (HCSWIT0035) and Blue (HCSWIT0036).

    £ 1.49
    In Stock
  • Quick view
    £ 3.49
    New

    These push buttons come with all necessary parts, including button, LED in holder, adapter ring, retaining nut and micro-switch. They are currently available in green (HCSWIT0032) and red (HCSWIT0029).

    £ 3.49
    In Stock
  • Quick view
    £ 3.49
    New

    These push buttons come with all necessary parts, including button, LED in holder, adapter ring, retaining nut and micro-switch. They are currently available in green (HCSWIT0032) and red (HCSWIT0029).

    £ 3.49
    In Stock
  • Quick view
    £ 0.99
    New

    These momentary on/off switches measure 27.65mm in length (including pins). The pins have a hole diameter of 3.8mm with a length of 6mm. These are available in both red (HCSWIT0025) and green (HCSWIT0026).

    £ 0.99
    In Stock
  • Quick view
    £ 0.99
    New

    These momentary on/off switches measure 27.65mm in length (including pins). The pins have a hole diameter of 3.8mm with a length of 6mm. These are available in both red (HCSWIT0025) and green (HCSWIT0026).

    £ 0.99
    In Stock
  • Quick view
    £ 3.49
    New

    This module contains a strip or 8 individually controllable RGB LEDs arranged in a serial (daisy-chain) configuration. Each LEDs reg, green, and blue, elements can be individually set to one of 256 intensity settings allowing a over 16 million colour variations to be set. The module also have power and data connection at moth ends so that multiple modes...

    £ 3.49
    In Stock
  • Quick view
    £ 8.99
    New

    A flexible full colour RGB LED light strip (HCOPTO0028). Each LED within the strip can be individually controlled to display any one of over 16 million colours. Each LED is connected in a serial chain meaning that each LED can be controlled with only one digital pin on a microcontroller. The strips are based on the WS2812 addressable RGB LEDs and are sold...

    £ 8.99
    In Stock
  • Quick view
    £ 4.99
    New

    Kingston Technology’s Secure Digital High Capacity (SDHC) memory cards are fully compliant with the latest SD Association specification. They are a performance class of SD memory cards designed to meet the storage demands of high-quality digital still and video cameras and other personal electronic devices, they work well with Arduino and are a...

    £ 4.99
    In Stock
  • Quick view
    £ 4.99
    New

    With a capacity of 8GB, these microSDHC/SDXC cards offer higher storage for your projects. The microSDHC cards allow you to maximise today’s revolutionary mobile devices. Kingston’s microSDHC cards use a speed “class” rating that guarantees a minimum data transfer rate for optimum performance with devices that use microSDHC/SDXC.

    £ 4.99
    In Stock
  • Quick view
    £ 2.39
    New

    Popular Atmel ATMega328P in a surface mount QFP package (HCCOIC0035) as used in development boards such as the Arduino Uno, Nano, Pro Mini etc.

    £ 2.39
    In Stock
  • Quick view
    £ 0.99
    New

    Murata CSTCE16M0V53-R0 (HCXTAL0006) 16MHz Chip type CERALOCK(R) with built-in load capacitors provides high accuracy in an extremely small package. MURATA's frequency adjustment and package technologyexpertise has enabled the development of the chip CERALOCK(R) with built-in load capacitors.

    £ 0.99
    In Stock
  • Quick view
    £ 3.49
    New

    The FT232R is the latest device to be added to FTDI’s range of USB UART interface Integrated Circuit Devices. The FT232R is a USB to serial UART interface with optional clock generator output, and the new FTDIChip-ID™ security dongle feature. In addition, asynchronous and synchronous bit bang interface modes are available. USB to serial designs using the...

    £ 3.49
    In Stock
  • Quick view
    £ 3.49
    New

    This tiny and low cost AVR development board is great for compact projects or projects that only requires a few IO pins. Based on the 8 pin Atmel ATTiny85 processor it allows for an incredibly small form factor. It also has the advantage of including a micro usb interface that allows the processor to be programmed via a USB power...

    £ 3.49
    In Stock
  • Quick view
    £ 27.99
    New

    The kit comprises the following items: Hobby Components R3 Mega Development Board Our very own version of the popular Arduino Mega development board (HCARDU0092). It hast been designed from the open source revision 3 Arduino Mega reference design and comes pre-flashed with the Arduino bootloader. This board is 100% compatible with all shields and modules...

    £ 27.99
    In Stock
  • Our very own version of the popular Arduino Mega development board (HCARDU0092). It hast been designed from the open source revision 3 Arduino Mega reference design and comes pre-flashed with the Arduino bootloader. This board is 100% compatible with all shields and modules compatible with the Arduno...

    £ 12.49
    In Stock
  • The Reptile V500 (HCRECO0002) is a low cost but big on features and versatility 500mm quadcopter frame. The two level design provides numerous options for mounting var...

    £ 21.99
    In Stock
  • Standard high quality 5mm LED in a coloured package. Suitable for power and status indicators, back-lighting, message displays, etc.  Pack of Ten.

    £ 1.49
    In Stock
  • Standard high quality 5mm LED in a coloured package. Suitable for power and status indicators, back-lighting, message displays, etc.  Pack of Ten.

    £ 1.49
    In Stock
  • Standard high quality 5mm LED in a coloured package. Suitable for power and status indicators, back-lighting, message displays, etc.  Pack of Ten.

    £ 1.49
    In Stock
  • This module is based on a touch-sensing IC (TTP223B) capacitive touch switch module. In its normal state, the module output is low and has a low power consumption; When touched the modules output turns high and if not touched for 12 seconds switches back to low-power mode.

    £ 2.49
    In Stock
  • This is an impressively low cost bundle of useful prototyping components. The pack consists of a range of discrete components, a breadboard and breadboard jumper cables. The bundle comes with a storage case making it great for students on the move or just as a useful collection of commonly used components. This kit includes the following items

    £ 12.99
    In Stock
  • This 8x8 serial dot matrix LED module (HCOPTO0014) allows you to experiment with dot matrix LED's without all the complicated wiring. The module makes use of the MAX7219 serial matrix LED driver which handles all the complicated stuff such as multiplexing the LEDs and driving them at the correct currents....

    £ 2.99
    In Stock
  • This controller is designed to be used with a RepRap RAMPS interface board such as our RAMPS compatible shield (HC3DPR0002). Using this module allows you to print your designes without requiring a computer be connected to your printer. The module contains and 20 x 4 line backlit LCD display, buzzer, SD card reader, and control inputs. The module also...

    £ 11.99
    In Stock
  • Quick view
    £ 2.99
    New

    The CH340 USB to serial adaptor (HCMODU0076) makes use of the CH340 USB to serial IC to provide a low cost alternative to our popular FTDI based module. Although much cheaper this module doesn't lack in features or usability.

    £ 2.99
    In Stock
  • Love building things out of building blocks as a kid? Love Arduino as an adult? This HobbyBlocks case kit combines both! Made entirely out of plastic building bricks, the case remains open across the top of your Arduino or Arduino compatible Uno R3 in order to allow you the freedom to access all ports and pins. While the majority of people will...

    £ 6.99
    In Stock
  •   Our biggest selling microcontroller development board (HCARDU0090). It hast been designed from the open source revision 3 Arduino Uno reference design and comes pre-flashed with the Arduino bootloader. This board is 100% compatible with all shields and modules designed for the Arduno Uno. If you are looking to get into microcontrollers, this is the...

    £ 8.49
    In Stock
  • The Hobby Components Microcontroller Experimenter's Kit is an ideal gift for anybody who wishes to get started in the world of microcontrollers and electronics and is designed to compliment most microcontroller and microcontroller development boards on the market. It contains a range of sensors and displays that allow you...

    £ 24.99
    In Stock
  • A very low cost module incorporating with a very high precision 24 ADC and differential high gain inputs designed to be interfaced with many common types of bridge sensors. E.g. pressure, strain, weight sensors. 

    £ 3.49
    In Stock
  • Standard high quality 5mm LED in a coloured package. Suitable for power and status indicators, back-lighting, message displays, etc. Pack of Ten.

    £ 1.49
    In Stock
  • 3 Review(s)

    Dan Howell created and uploaded the following video which demonstrates how to create a DIY Headtracker. Excellent video! Thanks Dan. Main parts for this are now available as a bundle containing the Pro Micro, GY-521, a switch and a 3 x 7 PCB. Custom PCBs are being made by the developers for this, and so..

    £ 9.69
    In Stock
  • This heatbed is designed to be compatible with any 3D printer that can accept the RAMPS MK2B version of heatbed. This heatbed has a dual power capability allowing it to be used with 12V or 24V power supply sources. It has a central mounting hole on the front side to allow for three point mounting.

    £ 8.99
    In Stock
  • This SD Card Shield is compatible with Arduino development boards that have the standard Arduino header layout. It can be directly plugged into and Arduino UNO, Leonardo, MEGA2560 or compatible motherboard and with the addition of an SD card add a huge data storage space to your Arduino project.

    £ 5.99
    In Stock
  • A microSD card reader and writer with included 3.3V regulator and level shifters making safe to interface with most 5V and 3.3V microcontrollers, including the Arduino Uno, Leonardo, Mega, Due, etc. The module uses an SPI interface for communication and is also compatible with the standard Arduino SD card library built into the Arduno IDE.

    £ 3.49
    In Stock
  • Quick view
    £ 3.99
    New

    This amazingly priced wireless module allows any microcontroller to connect to a 802.11b/g/n wireless network. This in turn provides your microcontroller project with the ability or request data from a server anywhere in the word via a suitable WiFI connection.

    £ 3.99
    In Stock
  • The Hobby Components Master Starter Kit is an ideal gift for anybody who wishes to get started in the world of Arduino microcontrollers and electronics. It contains a range of sensors and displays that allow you to experiment and develop software for typical Arduino based applications.

    £ 37.99
    In Stock
  • Quick view
    £ 5.99
    New

    This data logger shield provides an Arduino Uno, Leonardo, or Mega with the ability to log sensor data to an SD card with the minimum of set-up. The shield provides several useful features:

    £ 5.99
    In Stock
  • Quick view
    £ 3.49
    New

    This 16 key capacitive touch keypad is based on the TTP229 capacitive sensor with accurate sensing of up to 16 points. Using this keypad provides a solid state alternative to mechnical type keypads providing the advantage of greater durability especially in dusty environments.

    £ 3.49
    In Stock
  • Quick view
    £ 3.99
    New

    This expansion plate (HCCASE0008) is designed to expand the height of our Link Spite Arduino Uno/Mega case (HCCASE0003). This allows for additional electronics to be fitted inside such as most Arduino compatible shields or deeper LCD screens. The plate comes with all the required fixings. Multiple plates can be added with each expansion plate adding an...

    £ 3.99
    In Stock
  • Optical endstop providing a contactless and reliable alternative to the mechanical alternative. Although it is primarily intended to be used with 3D printers and CNC machines, it can be used for other projects such as rotary encoding, position sensing etc. The module comes complete with a cable measuring approximately 50cm.

    £ 2.49
    In Stock

Follow us on Facebook

  • Quick Dispatch

    All orders are dispatched within 24 hours. Special Delivery orders placed before 2pm are shipped the same day.

  • Contact Us

    We're available Monday to Friday 9am to 4:30pm and Saturday 9am to 12:30pm should you have a query about an order. Just have the order number to hand before you call.

  • Payment Methods

    We accept PayPal and Amazon Payments, both of which allow you to use all major credit and debit cards.

Support Forum

The best place for product information

Looking for schematics, example sketches, technical support, diagrams or just generally more information? Try the official Hobby Components Forum.