Shields

Active filters

  • WeMos V2 Relay Shield

    £3.33

    This relay shield is designed to be used with the WeMos mini & mini Pro ESP8266 based development boards (see item HCWEMO0002). Adding this shield to your WeMos mini development board provides it with the ability to switch high voltage, or high power devices from a single digital pin. Included with the shield is a set of...

    Out-of-Stock
  • WeMos D1 mini Prototyping...

    £2.08

    This prototyping shield is designed for use with the WeMos D1 mini and mini Pro development boards (see item HCWEMO0002). It allows you to create your own custom WeMos shield which can then be plugged directly into the WeMos mini. Supplied with the PCB are 3 sets of headers (requires soldering) which also allow for multiple shields to be stacked on top of each other. The PCB...

    Out-of-Stock
  • WeMos D1 Mini SD Card Shield

    £2.91

    This shield is designed for use with the WeMos D1 mini and mini Pro development boards (see item HCWEMO0002). The shield provides a means of allowing a WeMos D1 mini to directly communicate with most types of microSD card. The shield is also compatible with the standard Arduino SD card library. The shield is supplied with 3 sets of headers (requires soldering) which allow for multiple...

    Out-of-Stock
  • WeMos D1 Mini DHT Temp/Hum...

    £3.74

    The DHT Shield is a digital temperature and humidity sensor utilising the DHT11 sensor. Temperature range is 0~60C (+/-2C) and the humidity range is 20-90%RH (+/-5%RH). 

    Out-of-Stock
  • WeMos D1 Mini Motor Drive...

    £4.99

    The WeMos I2C Dual Motor Driver Module is designed to be able to drive up to two DC motors from your WeMos mini or mini Pro development boards (See HCWEMO0002). Using PWM the shield is capable of independently controlling the speed and direction of each connected motor with a maximum average of up to 1.2A (3.2A peak). The shield, together with its supplied...

    Out-of-Stock
  • WeMos D1 Mini Lithium...

    £4.16

    The WeMos lithium battery shield provides a means of powering your WeMos mini, or WeMos mini Pro (see item HCWEMO0002) from a single cell (3.7V) lithium battery. The shield contains a DC-DC converter to step-up the batteries 3.7V to 5V supplying...

    Last items in stock
  • WeMos D1 Mini WS8212 RGB...

    £2.91

    The WeMos WS2812B RGB Shield is a digital full colour (16777216 colour) RGB LED light source. It is specifically designed for the WeMos mini and mini Pro (see item HWEMO0002) ESP8266 based development boards. This shield includes two 8 pin headers...

    Last items in stock
  • WeMos D1 Mini OLED Shield

    £7.49

    The WeMos Mini D1 OLED shield is a tiny 0.66" 64 x 48 pixel OLED display. Using OLED display technology means that not only is the display very bright and clear with a high contrast ratio but has a much lower power consumption when compared to other display technologies such as back lit LCD. It is also very visible in both...

    Out-of-Stock
  • WeMos SHT30 Temp & Humidity...

    £4.58

    The WeMos SHT30 shield is a digital temperature and humidity sensor based upon the Sensirion SHT30 Sensor IC. This shield adds the ability to sense temperature to an accuracy of +/- 0.3oC and relative humidity to +/-3%. It is compatible with the WeMos mini, mini Pro (see item HWEMO0002), and mini lite (see item HCWEMO012) ESP8266/8285 based development boards. Although it is intended to be used...

    Last items in stock
  • WeMos Header Pin Set

    £1.24

    A set of 8 pin headers for WeMos boards and shields. This pack consist of 2 x long pin (10mm) female headers, 2 x short pin (3.25mm) female headers, and 2 x 11mm male header pins.

    Pins on all headers are standard 0.1" pitch.

    Last items in stock
  • Wemos Dual Base

    £2.08

    The Wemos dual base (HCWEMO0015) is designed to allow a Wemos shield to be connected to a Wemos D1 board without having to use the normal stacking method. This is useful when you have multiple shields that are not suited for stacking together such as an OLED shields with sensor/relays shields, or where a lower profile is preferred. Supplied with the shield is a set of four 8 pin female headers.

    In-Stock!
  • Wemos Triple Base

    £2.15

    The Wemos triple base (HCWEMO0016) is designed to allow a Wemos shield to be connected to a Wemos D1 board without having to use the normal stacking method. This is useful when you have multiple shields that are not suited for stacking together such as an OLED shields with sensor/relays shields, or where a lower profile is preferred. Supplied with the shield is a set of six 8 pin female headers.

    In-Stock!