3D Printing

  

Active filters

  • A4988 StepStick Compatible...

    £2.91

    This module is based upon the Allegro A4988 stepper motor driver and is ideal for use in 3D printer, CNC, and other applications where precise control of a stepper motor is required. Its pin....

    In Stock
  • Kapton Tape

    £2.91

    Kapton tapes are made from Kapton polyimide film with silicone adhesive. They are compatible with a wide temperature range as low as -269°C (-452°F) and as high as 260°C (500°F). An excellent addition to any 3D Printer's toolbox, this tape helps to keep your bed clean and gives excellent adhesion to prints. The tape is 20mm wide and the roll is 33 metres long, so it will last a while!

    In-Stock!
  • MK2B RAMPS Compatible Dual...

    £5.83

    This heatbed is designed to be compatible with any 3D printer that can accept the RAMPS MK2B version of heatbed. This heatbed has a dual power capability allowing it to be used with 12V or 24V power supply sources. It has a central mounting hole on the front side to allow for three point mounting.

    Last items in stock
  • MK7 / MK8 compatible 3D...

    £2.49
    Designed for Makerbot MK7/MK8 style of 3D printers. 
    Aluminium with anodized surface.
    Perfect for brass nozzle and barrels. Includes grub screw...
    In Stock
  • MK7 Compatible Extrusion...

    £1.83

    3d printer MK7 compatible stainless steel extrusion gear for 1.75mm filament. Includes grub screw...

    In Stock
  • Optical endstop for 3D...

    £2.08

    Optical endstop providing a contactless and reliable alternative to the mechanical alternative. Although it is primarily intended to be used with 3D printers and CNC machines, it can be used for other projects such as rotary encoding, position sensing etc. The module comes complete with a cable measuring approximately 50cm.

    In-Stock!
  • RAMPS compatible LCD...

    £6.66

    This controller is designed to be used with a RepRap RAMPS interface board such as our RAMPS compatible shield (HC3DPR0002). Using this module allows you to print your designes without requiring a computer be connected to your printer. The module contains and 20 x 4 line backlit LCD display, buzzer, SD card reader, and control inputs. The module also includes cables and adapter board for...

    In Stock
  • PTFE Tube for 1.75mm...

    £1.24

    This PTFE Tube is suitable for 1.75mm filament. Due to it's hard texture, this tubing is hard to damage and ages well. The tubes inner diameter is 2mm, and the outer diameter is 4mm. There are several advantages to PTFE, including its high working temperature of 250C. PTFE is non-toxic and corrosion resistant...

    In-Stock!
  • RepRap Mega Pololu...

    £4.16

    RepRap Arduino Mega Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy..


    In Stock
  • Heat Insulation Cotton...

    £1.66

    Heat insulation cotton is used in 3D printers on the nozzle to maintain warmth. The insulation cotton is made from heat-resistant ceramic fiber. This is of benefit as it helps to maintain temperature, thus saving power and decreasing the time it takes for the nozzle to get back up to temperature when your printer has been sat idle.

    Last items in stock
  • RepRap PCB Heat bed MK2a...

    £7.24

    The MK2a version of the heat bed PCB has a central mounting hole on the front side to allow for three point mounting. This is much easier for bed levelling in comparison to 4 point mounting. Additionally, the solder pads have been greatly increased in size, making it much easier and allowing for the use of 1206 surface mount components...

    Last items in stock
  • V1.2 Mechanical End stop...

    £1.24

    These mechanical end stops are quiet simply a means to an end. They detect when an x/y/z stage has reached its minimum or maximum. Excellent if you do not want to get bogged down in complicated light beam interrupters or flags. 

    In Stock