TELEPHONE LINES | Unfortunately due to the level of orders we are currently experiencing, we aren't always able to answer calls. If your query is urgent, please do leave a message or email sales@hobbycomponents.com and we will get back to you as soon as we are able. |
Motor Drivers
Active filters
-
Pulse / PWM generator for...
£9.99This pulse generator module is intended to be interfaced with common types of stepper / motor controllers. The module has two modes of operation, frequency and PWM. In frequency mode it will generate a square wave signal at a frequency that can b...
-
TB65603A Single Axis...
£6.66Description:
Recommended supply voltage DC 10V-24V.
Toshiba TB6560A controller.
High speed opto-couplers. -
4 DC Motor Drive module
£7.49Description:
This module uses the L293D chip and can drive 4 DC motors, and there is a 2 channel stepper motor port
Driver chips: L293D Dual H-Bridge Motor Driver IC
Drive part of the input voltage ... -
IRF520 MOSFET Driver Module
£2.08This little module (HCMODU0083) is a breakout board for the IFR520 MOSFET transistor. The module is designed to switch heavy DC loads from a single digital pin of your microcontroller. Its main purpose is to provide a low cost way to drive a DC motor for robotics applications, but the module can be used to control most high current DC loads. Screw terminals are provided to interface to...
-
L9110S DC Stepper Motor...
£1.66A very compact dual channel H-bridge motor driver module. The module incorporates two L9110S H-bridge driver IC's to allow either one stepper or two DC motors to be independently controlled. The module can accept a supply voltage between 2.5 to 12V allowing for motors within this supply...
-
L298N Stepper Motor Driver...
£3.33Uses ST' L298N chip, can directly drive two 3-30V DC motor, and provide a 5V output interface, power for 5V single-chip circuitry, supports 3.3VMCU control
-
A3967 Stepper Motor driver...
£2.08This EasyDriver compatible stepper motor driver module utilises the Allegro A3967SLB microstepping driver to proved a simple and compact means of driving bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors from a mirocontroller. By default the module will accept a 5V TTL...
-
Stepper Motor Driver HR4988
£2.41This module is based upon the HR4988 stepper motor driver and is ideal for use in 3D printer, CNC, and other applications where precise control of a stepper motor is required. Its pinnout is compatible with the StepStick design. This module can be used on its own (controlled by a microcontroller), or used with a RepRap compatible RAMPS shields such as our item number HC3DPR0002.
-
A4988 StepStick Compatible...
£2.91This module is based upon the Allegro A4988 stepper motor driver and is ideal for use in 3D printer, CNC, and other applications where precise control of a stepper motor is required. Its pin....
-
PCA9685 16ch 12bit...
£5.24This module (HCMODU0097) is a breakout board for the NXP PCA9685 16 channel PWM controller. It features 16 fully programmable PWM outputs with a 12bit resolution giving a total of 4096 programmable steps with a duty cycle being adjustable from 0% to 100%. Additionally, the output frequency of all 16 channels can be programmed...
-
Breakout board for A4988...
£3.74This item (HC3DPR0038) is a breakout out / adapter board for the low cost A4988 stepper motor driver board. It has a number of connectors that allow for easy interface of a stepper motor, power, and control signals to the A4988 driver module. Header sockets are provided so that the driver module can be easily inserted and removed from the breakout board. Standard 0.1" pitch headers...
-
NE555 Frequency Adjustable...
£1.24This is a square wave pulse generator module based on the ubiquitous NE555 timer IC. The module can be powered from a wide power supply range (4.5 to 12V) and will produce a continuous square wave output between 15Hz to 24KHz which can be set by on on-board multi-turn potentiometer. Useful for applications where an approximate...