Power

Active filters

  • Male DC Plug to 9V PP3...

    £0.58

    These battery clips (HCBATT0006) have a standard male 2.1mm DC connector at one end and a PP3 9V battery clip / buckle at the other. The wire measures approximately 7.5cm. The D.C connector has the positive at the tip making it suitable for most Arduino boards with a DC connector.

    In-Stock!
  • 4 x AA Battery Box

    £1.24

    This battery box (HCBATT0016) holds 4 standard AA batteries and its open design allows for easy insertion and removal of batteries. The holder has colour coded wires with tinned ends to make soldering as easy as possible. It has two mounting holes for permanently fixing it to a surface.


    Image

    Product code: HCBATT0016
    Dimensions: 6.2 x 6 x 1.5
    Battery Type: 4 x AA
    Mounting hole size: 3.8mm

    In-Stock!
  • 5.5 X 2.1mm DC Socket to...

    £1.08

    This is a Female 5.5 x 2.1mm Power sockets ideally suited to connecting to DC jacks that then adapts to two screw terminals. The sockets function by separating the central core and outer component of the jack and passing these through to screw terminals. The adapter is solidly constructed and housed in rubber to allow repeated use.

    In-Stock!
  • 6 AA cell ABS plastic...

    £1.66

    6x AA cell ABS plastic battery holder (HCBATT0006) allowing for easy insertion and removal of batteries. The holder has colour coded wires with tinned ends allowing for easy solder to a PCB or terminal. It has two mounting holes for permanently fixing to a surface. Depending on battery type fitted this holder can provide approximately 6V DC for remotely powering your projects.

    In Stock
  • XL60009 DC-DC Step-up Boost...

    £2.49

    This XL6009 DC-DC boost/step-up converter module (HCMODU0091) is based on the XLSemi XL6009 DC-DC converter and is capable of boosting a wide range of input voltages up to a maximum of 45V. It output can supply up to 2.5A out current (dependent on input voltage and operating environment) and has built in thermal limiting protection circuitry...

    In-Stock!
  • LM2596 DC-DC 3-35V...

    £1.66

    This DC to DC Step-Down Adjustable Power Supply Module is based on the LM2596 switching regulator...

    In Stock
  • Euro to UK Plug Adapter

    £1.49

    This adapter converts CEE7 (XVI) Euro plug to standard UK 3 pin plug. Fused at 3A, this plug is constructed using tough thermoplastic nylon. It is a simple, safe and quick method of converting euro plugs for use is UK sockets. There is no need to strip cables or remove existing plugs...

    Out-of-Stock
  • 4Pk NIMH AccuDigital...

    £4.16
    • 1300mAh capacity
    • Size: AA
    • NiMH rechargeable
    • 1000 charges (approx.)
    • Packaging: 4 pack blister card - RRP: £5.99
    In-Stock!
  • USB to 2.1mm Jack cable...

    £2.49

    A USB to 2.1mm DC jack cable with a built-in DC to DC step up converter which will convert the 5V DC voltage supplied by a USB socket up to 9V DC at the jack socket. This makes the cable useful for powering electronics and projects from a standard USB port or charger where 5V is insufficient voltage.

    In-Stock!
  • Hobby Components Lithium...

    £2.08

    The Hobby Components micro charger is a tiny single cell (3.7V) lithium battery charger module which not only incorporates both battery charging protection and control, but also includes battery voltage & current over discharge protection and battery overload protection. Measuring only 27 x 14mm this tiny module can easily be incorporated into low power lithium battery applications.

    The charger will accept power from either a 5V microUSB adapter or via a 4.5 to 6V power supply and will charge a connected single cell lithium battery at a rate of ~0.5A.

    The battery can be connected via a JST XH-2.54 connector or by 2 large solder pads (BIN + & BIN -).

    The module's output supplies the batteries nominal output of 3.7V (4.2V whilst charging) at a constant current of up to 2A (depending on battery and charger specification). An external device can be connected to this output via a 0.1” pitch pin header or via 2 large solder terminals (BOUT + & GND).



    Image

    Supported battery type:						Single cell Lithium-ion battery
    Module supply voltage:						5V via microUSB or 4.5 to 6V via power in header
    Battery charge voltage max (float):				4.2V
    Battery stand-by exit voltage:					4.05V
    Battery charge current (max):					445mA +/- 10%
    Battery charge termination current:				44.5mA +/- 10%
    Battery over discharge voltage protection:			2.4V
    Battery over discharge current protection:			3.5A +/- 0.9A
    BAT out terminal voltage max (charging):			4.3V
    BAT out terminal voltage min (discharging):		2.9V
    BAT out terminal maximum continuous current:		2A
    Module dimensions:							27 x 14 x 7.5mm






    Battery In And Power Out Connection:

    Image



    External Power Options:

    Image

    PDF available for download on our support forum here.

    In-Stock!
  • 4Pk NIMH AccuDigital...

    £3.74
    • 900mAh capacity
    • Size: AAA
    • NiMH rechargeable
    • 1000 charges (approx.)
    • Packaging: 4 pack blister card - RRP: £4.99
    In-Stock!
  • 5.5 x 2.1mm DC Socket...

    £1.08

    This is a male 5.5 x 2.1mm Power sockets ideally suited to connecting to DC jacks that then adapts to two screw terminals. The sockets function by separating the central core and outer component of the jack and passing these through to screw terminals. The adapter is solidly constructed and housed in rubber to allow repeated use.

    In-Stock!