mLink L9110 DC Motor...
The mLink L9110 motor controller is a serial (I2C) 2 channel DC motor driver that is capable...
The Hobby Components micro charger is a tiny single cell (3.7V) lithium battery charger module which not only incorporates both battery charging protection and control, but also includes battery voltage & current over discharge protection and battery overload protection. Measuring only 27 x 14mm this tiny module can easily be incorporated into low power lithium battery applications.
The charger will accept power from either a 5V microUSB adapter or via a 4.5 to 6V power supply and will charge a connected single cell lithium battery at a rate of ~0.5A.
The battery can be connected via a JST XH-2.54 connector or by 2 large solder pads (BIN + & BIN -).
The module's output supplies the batteries nominal output of 3.7V (4.2V whilst charging) at a constant current of up to 2A (depending on battery and charger specification). An external device can be connected to this output via a 0.1” pitch pin header or via 2 large solder terminals (BOUT + & GND).
The Hobby Components micro charger is a tiny single cell (3.7V) lithium battery charger module which not only incorporates both battery charging protection and control, but also includes battery voltage & current over discharge protection and battery overload protection. Measuring only 27 x 14mm this tiny module can easily be incorporated into low power lithium battery applications.
The charger will accept power from either a 5V microUSB adapter or via a 4.5 to 6V power supply and will charge a connected single cell lithium battery at a rate of ~0.5A.
The battery can be connected via a JST XH-2.54 connector or by 2 large solder pads (BIN + & BIN -).
The module's output supplies the batteries nominal output of 3.7V (4.2V whilst charging) at a constant current of up to 2A (depending on battery and charger specification). An external device can be connected to this output via a 0.1” pitch pin header or via 2 large solder terminals (BOUT + & GND).
Supported battery type: Single cell Lithium-ion battery Module supply voltage: 5V via microUSB or 4.5 to 6V via power in header Battery charge voltage max (float): 4.2V Battery stand-by exit voltage: 4.05V Battery charge current (max): 445mA +/- 10% Battery charge termination current: 44.5mA +/- 10% Battery over discharge voltage protection: 2.4V Battery over discharge current protection: 3.5A +/- 0.9A BAT out terminal voltage max (charging): 4.3V BAT out terminal voltage min (discharging): 2.9V BAT out terminal maximum continuous current: 2A Module dimensions: 27 x 14 x 7.5mm
Battery In And Power Out Connection:
External Power Options:
The mLink L9110 motor controller is a serial (I2C) 2 channel DC motor driver that is capable...
PLEASE NOTE THAT THIS KIT IS NOW SHIPPED WITH OUR UNO+ Development Board (See SKU:...
The Hobby Components prototyping shield for the Arduino Uno allows you to add your own custom...
The Hobby Components logic analyser can capture up to 16 separate channels of 3.3V or 5V logic...
The Hobby Components prototyping shield for the Arduino Mega allows you to add your own custom...
Additional add-on for our V2 4x4x4 Cube Kits. This PCB template has been designed to make...
This is our lower cost alternative to the standard R3 Uno, but in this case lower cost doesn't...
This module uses a set of transistors with pullup resistors to provide a 2 channel...
Our very own version of the popular Arduino Mega development board (HCARDU0092). It hast been...
The mLink 12-Channel Servo Controller allows you to independently control up to 12 servos per...
The mLink WS2812 LED driver is a serial (I2C) module intended for driving WS2812 5V RGB LEDs....
Our Ultimate Sensor Kit has been revamped, and, unlike most in the market, is mercury free! It...
The 1602 SmartLCD module is a serially controlled 2 line by 16 character alphanumeric...
LED light cubes are a hugely popular and fun project. With this kit (HCKITS0050) you will have...